All geek questions in one place

Linux 4.5 Interrupting GPIO via Devicetree on Xilinx Zynq Platform

I am using a custom development panel with the Zynq XC72010 used to run the Linux 4.5 kernel. I am developing a device driver for the chip that we are testing in the house, and I have many problems trying to connect the GPIO line to the software IRQ. So far I have tried several methods and have exhausted any Google search I can think of. Relevant parts of my devicetree configuration:

/ {
    compatible = "xlnx,zynq-7000";

    amba {
        compatible = "simple-bus";
        #address-cells = <1>;
        #size-cells = <1>;
        interrupt-parent = <&intc>;
        ranges;

        intc: interrupt-controller@f8f01000 {
            compatible = "arm,cortex-a9-gic";
            #interrupt-cells = <3>;
            interrupt-controller;
            reg = <0xF8F01000 0x1000>,
                  <0xF8F00100 0x100>;
        };

        i2c0: i2c@e0004000 {
            compatible = "cdns,i2c-r1p10";
            status = "disabled";
            clocks = <&clkc 38>;
            interrupt-parent = <&intc>;
            interrupts = <0 25 4>;
            reg = <0xe0004000 0x1000>;
            #address-cells = <1>;
            #size-cells = <0>;

            // I WANT INTERRUPT TO TRIGGER
            // ON THIS DEVICE (axi_gpio_0, pin 2)
            device: device@48 {
                compatible = "device,name";
                reg = <0x48>;
                reset-gpios = <&axi_gpio_0 1 0>;
                interrupt-parent = <&axi_gpio_0>;
                interrupt-gpios = <&axi_gpio_0 2 0>;
            };
        };
    };

    amba_pl {
        #address-cells = <1>;
        #size-cells = <1>;
        compatible = "simple-bus";
        ranges ;
        axi_gpio_0: gpio@41200000 {
            #gpio-cells = <2>;
            compatible = "xlnx,xps-gpio-1.00.a";
            gpio-controller;
            interrupt-parent = <&intc>;
            interrupts = <0 31 4>;
            reg = <0x41200000 0x10000>;
            xlnx,all-inputs = <0x0>;
            xlnx,all-inputs-2 = <0x0>;
            xlnx,all-outputs = <0x0>;
            xlnx,all-outputs-2 = <0x0>;
            xlnx,dout-default = <0x00000000>;
            xlnx,dout-default-2 = <0x00000000>;
            xlnx,gpio-width = <0x10>;
            xlnx,gpio2-width = <0x20>;
            xlnx,interrupt-present = <0x1>;
            xlnx,is-dual = <0x0>;
            xlnx,tri-default = <0xFFFFFFFF>;
            xlnx,tri-default-2 = <0xFFFFFFFF>;
    };
};

I am trying to assign an interrupt to pin 2 "axi_gpio_0" inside the "device".

Browsing google gave 3 common interrupt binding methods in driver code:

/* Method 1 */
device->interrupt_gpio = devm_gpiod_get_optional(&i2c_client->dev,
                                        "interrupt", GPIOD_IN);

if(IS_ERR(device->interrupt_gpio))
    return PTR_ERR(device->interrupt_gpio);

printk("device: Interrupt GPIO = %d\n",desc_to_gpio(device->interrupt_gpio));

irq = gpiod_to_irq(device->interrupt_gpio);
printk("device: IRQ = %d\n",irq);

ret = devm_request_threaded_irq(&i2c_client->dev, irq,
    NULL, device_irq_thread, IRQF_ONESHOT | IRQF_TRIGGER_HIGH,
    "device", device);
if (ret != 0)
    dev_err(&i2c_client->dev, "Failed to request IRQ: %d\n", ret);



/* Method 2 */
device->interrupt_gpio = devm_gpiod_get_optional(&i2c_client->dev,
    "interrupt", GPIOD_ASIS);

if (IS_ERR(device->interrupt_gpio))
    return PTR_ERR(device->interrupt_gpio);


if (device->interrupt_gpio) {
    dev_info(&i2c_client->dev, "Found interrupt GPIO: %d\n",desc_to_gpio(device->interrupt_gpio));
    dev_info(&i2c_client->dev, "IRQ Number: %d\n",gpiod_to_irq(device->interrupt_gpio));

    gpio_request(desc_to_gpio(device->interrupt_gpio), "DEVICE_INT");    // Request a GPIO pin from the driver
    gpio_direction_input(desc_to_gpio(device->interrupt_gpio));           // Set GPIO as input
    gpio_set_debounce(desc_to_gpio(device->interrupt_gpio), 50);          // Set a 50ms debounce, adjust to your needs
    gpio_export(desc_to_gpio(device->interrupt_gpio), false);                    // The GPIO will appear in /sys/class/gpio

    ret = request_irq(gpiod_to_irq(device->interrupt_gpio),             // requested interrupt
                   (irq_handler_t) irqHandler,  // pointer to handler function
                   IRQF_TRIGGER_RISING,         // interrupt mode flag
                   "DEVICE_IRQ_HANDLER",        // used in /proc/interrupts
                   NULL);                       // the *dev_id shared interrupt lines, NULL is okay
    if (ret != 0) {
        dev_err(&i2c_client->dev,
            "Failed to request IRQ: %d\n", ret);
    }
}
else {
    dev_err(&i2c_client->dev, "Failed to get interrupt GPIO pin\n");
}



/* Method 3 */
dev_info(&i2c_client->dev, "IRQ requested: %d\n", i2c_client->irq);

ret = devm_request_threaded_irq(&i2c_client->dev, i2c_client->irq,
NULL, device_irq_thread, IRQF_ONESHOT | IRQF_TRIGGER_LOW,
"device", device);
if (ret != 0)
    dev_err(&i2c_client->dev, "Failed to request IRQ: %d\n", ret);

I tried combinations of all these methods and various devicetree configurations, but none of them reached the required functionality.

Method 1 leads to this conclusion:

device: Interrupt GPIO = 892
device: IRQ = -6
device 0-0048: Failed to request IRQ: -22

2 :

device 0-0048: Found interrupt GPIO: 892
device 0-0048: IRQ Number: -6
device 0-0048: Failed to request IRQ: -22

, GPIO GPIO api .

3, devicetree:

device: device@48 {
    compatible = "device,name";
    reg = <0x48>;
    interrupt-parent = <&axi_gpio_0>; // or <&intc>?
    interrupts = <0 2 0x02>; // trying to grab pin 2
};

3 :

genirq: Setting trigger mode 2 for irq 168 failed (gic_set_type+0x0/0x48)
device 0-0048: IRQ requested: 168
genirq: Setting trigger mode 8 for irq 168 failed (gic_set_type+0x0/0x48)
device 0-0048: Failed to request IRQ: -22

, GPIO Linux. , . .

1:

, Linux . 3:

device: device@48 {
    compatible = "device,name";
    reg = <0x48>;
    interrupt-parent = <&axi_gpio_0>;
    interrupts = <0 2 0x04>;
};

:

dev_info(&i2c_client->dev, "IRQ requested: %d\n", i2c_client->irq);

ret = devm_request_threaded_irq(&i2c_client->dev, i2c_client->irq,
NULL, device_irq_thread, IRQF_ONESHOT | IRQF_TRIGGER_HIGH,
"device", device);
if (ret != 0)
    dev_err(&i2c_client->dev, "Failed to request IRQ: %d\n", ret);

IRQ. , , . , , axi_gpio_0 pin 2 . intc, axi_gpio_0 interrupt-parent, IRQ ( cat /proc/interrupts). , , , axi_gpio_0 2?

2:

: kernel/drivers/irqchip/irq-gic.c. :

static int gic_set_type(struct irq_data *d, unsigned int type)
{
    void __iomem *base = gic_dist_base(d);
    unsigned int gicirq = gic_irq(d);

    /* Interrupt configuration for SGIs can't be changed */
    if (gicirq < 16)
        return -EINVAL;

    /* SPIs have restrictions on the supported types */
    if (gicirq >= 32 && type != IRQ_TYPE_LEVEL_HIGH &&
                type != IRQ_TYPE_EDGE_RISING)
        return -EINVAL;

    return gic_configure_irq(gicirq, type, base, NULL);
}

- , , :

/* SPIs have restrictions on the supported types */
/*if (gicirq >= 32 && type != IRQ_TYPE_LEVEL_HIGH &&
            type != IRQ_TYPE_EDGE_RISING)
return -EINVAL;*/

. .

UPDATE:

IRQ GPIO. GPIO, . IP- Xilinx Zynq, GPIO ( ). , GPIO , , Linux .

, GPIO, compatible = "xlnx,xps-gpio-1.00.a";, Linux. , GPIO.

.

+4
1

node 3, IRQ irq_of_parse_and_map(i2c_client->dev.of_node, 0).

IRQ , , devm_request_threaded_irq().

0

Source: https://habr.com/ru/post/1652905/

More articles:


All Articles